Finished size: about 7.5 in (19 cm) long, fits a hand 7–8 in (18–20 cm) around — adult medium Difficulty: Easy | Hook: 4.0 mm | Yarn: DK weight
This is an original pattern guide. Size depends on your yarn, hook and tension — check your gauge first.
Materials
• Yarn: DK (light worsted, 8-ply) yarn — emerald green about 90 g / 200 m (220 yds), and cream about 25 g / 55 m (60 yds) for the cuff.
• Hook: 4.0 mm crochet hook.
• Extras: yarn needle, scissors, tape measure, 2 stitch markers.
• Gauge: 16 half double crochet (hdc) and 12 rows = 4 in (10 cm). If your stitches are tighter, go up to a 4.5 mm hook; if looser, try 3.5 mm.
Yarn amounts
The amounts above make one pair in adult medium. For a smaller hand, work fewer cuff rows and fewer hand rounds (see the sizing notes). Allow a little extra yarn if your tension is loose.
Abbreviations (US terms)
ch chain
sl st slip stitch
sc single crochet
hdc half double crochet
dc double crochet
BLO back loop only
st(s) stitch(es)
rep repeat
Pattern — Make 2 Gloves the Same
Work the cuff in rows first, join it into a ring, then work the hand in rounds. Do not turn at the end of hand rounds unless the pattern says so. Use a stitch marker to mark the first stitch of each round.
Step 1 — Ribbed Cuff (cream yarn)
Ch 13.
Row 1: Hdc in the 2nd ch from the hook and in each ch across. (12 sts)
Row 2: Ch 1, turn. Hdc in the BLO of each st across. (12 sts)
Rows 3–28: Repeat Row 2. The cuff strip should measure about 7 in (18 cm) long. For a smaller wrist, stop at 26 rows; for a larger wrist, work 30 rows.
Fold the strip in half, matching the short ends. Sl st the two short edges together through both layers to form a ring. Turn the cuff right side out. Do not fasten off — or fasten off and join the green yarn at the same place
Step 2 — Hand (emerald green yarn)
Join the green yarn at the top edge of the cuff ring. Work in rounds around the edge.
Round 1: Ch 1 (does not count as a st). Work 28 hdc evenly spaced around the top edge of the cuff. Join with a sl st to the first hdc. (28 sts)
Rounds 2–5: Ch 1, hdc in each st around, join. (28 sts each round)
Round 6 — thumb opening: Ch 1, hdc in the next 22 sts, ch 6, skip the next 6 sts, join with a sl st to the first hdc. (22 hdc + 6 ch = 28 sts)
Round 7: Ch 1, hdc in each of the next 22 sts, then hdc in each of the 6 ch, join. (28 sts) Rounds 8–11: Ch 1, hdc in each st around, join. (28 sts each round)
Round 12 — shell border: Ch 1, sc in the first st, *skip 1 st, 5 dc in the next st, skip 1 st, sc in the next st; rep from * around. You will make 7 shells. Join with a sl st to the first sc. (7 shells = 35 dc + 7 sc)
Fasten off and weave in the end.
Step 3 — Thumb
Join the green yarn at the thumb opening (the 6 skipped sts and the 6 ch from Round 6).
Round 1: Ch 1, work 12 hdc evenly around the opening — 6 in the skipped sts and 6 in the ch. Join with a sl st. (12 sts)
Round 2: Ch 1, hdc in each st around, join. (12 sts)
Round 3: Ch 1, sc in each st around, join. (12 sts) Fasten off and weave in the end. Repeat Steps 1–3 for the second glove.
Finishing & Blocking
• Weave in all loose ends with the yarn needle, following the stitch path so they stay hidden. • Lightly steam or wet-block the gloves: lay them flat, shape the cuff and fingers, and leave to dry fully. Blocking evens out the shell border and softens the ribbing.
• Try both gloves on before the final weave-in, and check the thumb opening sits comfortably.
Care
• Hand wash in cool water with a mild detergent. Do not wring — press the water out gently in a towel.
• Lay flat to dry, away from direct sunlight, so the gloves keep their shape.
Troubleshooting
• Cuff too tight or too loose? Add or remove 2 cuff rows at a time (each row is about 0.25 in). The cuff should stretch a little around the wrist.
• Hand too narrow? Your gauge may be tight — try a 4.5 mm hook, or add 4 sts in Round 1 (32 sts) and keep 32 sts through every round; the shell border then makes 8 shells. • Thumb opening too small? In Round 6, chain 7 and skip 7 sts instead of 6, and work 14 sts around the thumb opening.
• Shell border curling? Block it flat while damp, and make sure the 5-dc shells are not worked too tightly.
